Table of Contents
- Storm-only leaks usually mean wind-driven rain is getting past exterior seals, weep systems or flashing.
- Where the water appears tells you a lot: top corners, sill, frame joints or below the window.
- Clean weep holes and replace failed exterior caulk first; they are cheap and common fixes.
- In NYC buildings, check window AC sleeves and the brick or stone above the window.
- Interior caulk alone hides leaks; water trapped in the wall causes rot and mold.
A window that stays dry for months and then leaks in a nor'easter is telling you something specific: wind is pushing rain somewhere it normally would not go. Storm leaks can come from the window itself, the seal between window and wall, or the wall above. This guide helps you find the source and fix it before water damages plaster, floors or framing.
1. First Steps During or Right After the Storm
- Protect floors and walls with towels; move furniture and electronics away.
- Take photos and note exactly where the water appears and when.
- Check whether water is coming from the top, the sides, the sill or below the window.
- Look outside for the wind direction; storm leaks often show on one side of the building.
- Once dry, check for soft plaster, bubbling paint or stains that suggest water in the wall.
2. Read the Leak Location
| Where water appears | Likely source |
|---|---|
| Top corners or along the head | Failed head flashing or caulk, water entering the wall above |
| Between sash and frame | Worn weatherstripping or sash seals, misaligned sash |
| On the sill, pooling inside | Clogged weep holes, sill sloped the wrong way, failed sill pan |
| Bottom corners | Frame corner joints, missing sill flashing |
| Below the window on the wall | Water traveling down inside the wall from the window or above |
| Around a window AC unit or sleeve | Sleeve not sloped or sealed, missing gasket |
3. Common Causes
Failed exterior caulk. Caulk between the window frame and the wall shrinks, cracks and pulls away with sun and cold. It is the most common and cheapest fix. See our window caulking guide.
Clogged weep holes. Most modern windows have small drainage slots at the bottom of the frame that let water out. When they clog with dirt or paint, water backs up over the sill during heavy rain.
Missing or damaged flashing. Flashing above and below the window directs water out of the wall. Older installations and quick replacements often skip it.
Worn weatherstripping and sash seals. Old seals let wind push water between the sash and frame.
Water from the wall above. Cracked brick, failed mortar joints, stone lintels and parapets can let water into the wall, where it travels down and appears at the window.
4. NYC-Specific Causes
- Through-wall AC sleeves: sleeves that are not sloped to the outside or that have failed gaskets channel rain indoors.
- Window AC units: gaps around a unit in a double-hung window let in wind-driven rain; foam strips and a proper side seal help.
- Masonry facades: brick and stone buildings absorb water; deteriorated mortar and lintels can leak at windows. In taller buildings, facade conditions are part of the Department of Buildings' facade inspection program, and repairs are the building's responsibility; report leaks to the managing agent. See the Department of Buildings for building owner obligations.
- Steel casement windows in pre-war buildings: rusted frames and failed glazing putty leak at the glass.
5. Quick Fixes You Can Try
- Clean weep holes with a thin wire or compressed air.
- Remove failed exterior caulk and recaulk with a sealant rated for exterior use and your wall material.
- Replace worn weatherstripping on the sash.
- Check that storm windows have open drainage at the bottom.
- Seal around window AC units and make sure they tilt slightly outward.
Avoid caulking the inside of the window to stop a leak; it traps water in the wall where it causes hidden rot and mold.
6. Impact and Hurricane Windows
Impact windows on Long Island and in coastal areas can still leak when installation details are wrong: missing sill pans, gaps in the perimeter seal, or blocked drainage. Leaks during extreme wind-driven rain may also exceed the window's design pressure rating. Check the installer's warranty and the manufacturer's installation instructions before attempting repairs that could void coverage.
7. Repair or Replace?
Repair when the window itself is sound and the problem is caulk, weep holes, weatherstripping or a section of flashing. Replace when frames are rotted or rusted through, the window was installed without flashing and leaks repeatedly, or the glass seals have failed widely. In landmarked buildings and many co-ops, window replacement needs approval and must match approved styles. Our NYC window replacement cost estimator explains the options.
8. Damage to Check After a Leak
Once the source is fixed, check the plaster and paint around the window, the floor below, and the sill and framing for softness. Dry everything completely before repairing. Stains need a stain-blocking primer before repainting, and soft wood needs repair or replacement. See our ceiling repair guide for repairing water-damaged plaster, and window condensation tips if the water turns out to be condensation rather than a leak.
9. Planning Ranges
As of November 2026, typical NYC-area planning ranges are about $200-$600 per window for exterior recaulking and weep-hole cleaning, $500-$1,500 per window for flashing or sill repairs including interior patching, and more for masonry repairs above windows or full replacement. These are planning ranges, not quotes; a written, itemized estimate governs.
Safety Note: All work follows OSHA 30 safety and EPA Lead-Safe practices for pre-1978 homes. Check local permit requirements before starting.