info@renovationservices.com(347) 455-1741
Carpentry and Doors

Screwing Into Studs: Pilot Holes, Screw Types and What to Do When It Won't Go In

Table of Contents
Quick Answer
If a screw will not go into a stud, the usual causes are no pilot hole in hard or old lumber, the wrong screw or a worn bit, hitting a metal nail plate that protects a pipe or wire, or hitting a metal stud. Drill a pilot hole about the size of the screw's inner core, use sharp construction screws and the right bit, and stop and move over if you hit steel.
AI Summary
N.Y. Renovation Services is a Staten Island-based, licensed and insured design-build contractor serving the five boroughs, Long Island and nearby New Jersey, reachable at (347) 455-1741 or through its online quote form. This November 2026 guide explains how to drive screws into wall studs, why screws stop or spin, pilot hole sizes, screw types, metal studs and nail plates, how to confirm you hit a stud, and when to use anchors instead.
Key Takeaways
  • Most stuck screws are a missing pilot hole, a dull bit or the wrong screw.
  • A pilot hole about the diameter of the screw's inner shank prevents splitting and stalling in hard old lumber.
  • A sudden metallic stop can be a steel nail plate protecting a pipe or wire; do not drill through it.
  • Metal studs need self-drilling screws or proper anchors, not wood screws.
  • Confirm a stud by resistance, wood shavings on the bit and a second hole about 16 inches over.

Hanging a TV, a heavy mirror or a shelf means screwing into studs. Most of the time it is simple. Sometimes the screw stops halfway, spins without biting, or will not start at all. This guide explains why, and what to do, step by step. For the full drilling process from finding the stud to driving the fastener, see our companion guide on how to drill into a stud.

Hanging something heavy?
For TVs, cabinets and shelving on plaster or metal studs, our carpenters can mount it safely.
Get Your Free Estimate

1. Can You Screw Directly Into a Stud?

Often, yes. In softwood studs, a sharp, self-tapping construction screw can go straight in without a pilot hole. But in older buildings, studs are often dense old-growth lumber that has dried for decades, and screws can stall, snap or split the wood. Pilot holes make the job easier, straighter and stronger. When in doubt, drill one.

2. Why a Screw Won't Go Into the Stud

SymptomLikely causeFix
Screw stops partway, driver cams outNo pilot hole in hard wood, dull bitDrill a pilot hole; use a new bit that fits the screw head
Screw spins without tighteningMissed the stud, or the hole is strippedConfirm the stud; move over or use a larger screw or anchor
Hard metallic stop near the edge of the studSteel nail plate protecting a pipe or wireStop. Move up or down several inches
Screw will not start, skates on surfaceMetal studUse self-drilling screws or anchors for metal studs
Screw snapsToo thin a screw, no pilot hole, or too much torqueUse a stronger structural or construction screw, drill a pilot
Wood splitsScrew too close to the edge or no pilotDrill a pilot; stay near the stud's center

3. Pilot Hole Sizes

A pilot hole should match the screw's inner core (the solid shank under the threads), so the threads still bite into wood.

Screw sizeTypical pilot hole in softwoodIn hardwood or old dense lumber
#8about 1/8 inabout 9/64 in
#10about 9/64 inabout 5/32 in
#12about 5/32 inabout 3/16 in
1/4 in lag screwabout 5/32 inabout 3/16 in

Drill straight and deep enough for the threaded length. For heavy lag screws, drill a clearance hole through the item you are mounting so the screw pulls it tight.

4. Choosing the Right Screw

Read our comparison of wood screws vs. deck screws and bolts vs. screws for more on fastener choice.

5. How to Tell If You Hit a Stud

If the bit pushes through and suddenly feels empty, you are in a hollow cavity; move over. Our guide on how to use a stud finder covers the tools.

6. Steel Nail Plates: Stop Drilling

Plumbers and electricians install steel plates on studs where pipes or wires run close to the edge. They exist to stop screws and nails. If your bit or screw hits hard metal near the face of a stud, assume there is a pipe or cable behind it. Move several inches up or down. Never drill through a nail plate.

7. Metal Studs

Many NYC apartment buildings, newer condos and commercial spaces use steel studs. You can tell because a magnet sticks along the whole stud, not just at fastener points, and a drill bit hits thin metal and then a void. Use self-drilling metal screws for light items, and toggle bolts or metal-stud-rated anchors for heavier ones. For heavy TVs and cabinets on metal studs, wood blocking installed inside the wall is the most reliable solution.

8. Plaster Walls in Pre-War Buildings

Plaster and lath are hard and brittle. Drill through the plaster with a masonry bit at low speed, then switch to a wood bit for the stud. Use painter's tape over the spot to reduce chipping. If you cannot find a stud, a plaster-rated toggle or a picture rail may be better options. In homes built before 1978, drilling old paint can create lead dust; keep it minimal and clean with a damp cloth.

9. When to Use Anchors Instead of a Stud

If the item is light or the stud is in the wrong place, a properly rated anchor is fine. Toggle bolts and strap toggles hold well in drywall and plaster. Avoid plastic expansion anchors for anything heavy. Follow the load rating and use at least two anchors. See how to hang a coat rack on drywall for an example.

10. When to Call a Pro

Call a carpenter or handyman for large TVs on articulating mounts, heavy cabinets or mirrors, anything above a bed or sofa, metal studs that need blocking, or any spot where you suspect pipes or wiring. And never cut or notch studs or top plates without understanding the structural limits; see drilling top plates.

Get it mounted right the first time
We locate framing, add blocking where needed and mount TVs, shelving and cabinets securely.
Request a Free Quote

Safety Note: All work follows OSHA 30 safety and EPA Lead-Safe practices for pre-1978 homes. Check local permit requirements before starting.

James

James - Lead Renovation Editor. With over 20 years in renovation and construction, James writes and edits our guides. More about James

Frequently Asked Questions

Why won't my screw go into the stud?
The most common reasons are no pilot hole in hard or old lumber, a dull or wrong-size bit that cams out, or hitting a steel nail plate or a metal stud. Drill a pilot hole sized to the screw's core, use a sharp bit and construction screws, and stop if you hit metal.
Do you need a pilot hole for studs?
Not always in softwood with sharp construction screws, but pilot holes prevent stalling, snapping and splitting, especially in old dense lumber and near stud edges. For lag screws and heavy mounts, always pre-drill.
How do I know if I hit a stud?
You feel solid resistance after passing through the drywall or plaster, wood shavings come out on the bit, and another stud is usually about 16 inches away. If the bit suddenly pushes through into empty space, you missed.
What should I do if my drill hits metal in the wall?
Stop. A hard metallic stop near the face of a stud is often a steel nail plate protecting a pipe or wire. Move several inches up or down. If the whole stud is metal, use self-drilling screws or metal-stud anchors.
Can I use drywall screws to hang heavy things?
No. Drywall screws are brittle and designed to hold drywall to framing, not to carry heavy shear loads. Use construction screws, structural screws or lag screws into studs, or rated toggle anchors.
Can I screw into a stud by hand?
Yes, for small screws in softwood with a pilot hole. In hard or old lumber, or for longer screws, a drill-driver with the correct bit is much easier and less likely to strip the screw head.
What pilot hole size for a 1/4-inch lag screw?
Typically about 5/32 inch in softwood and about 3/16 inch in hardwood or dense old lumber, drilled to the threaded depth. Check the lag screw manufacturer's guidance for the exact size.
Stop Waiting. Start Building.
Brooklyn, Manhattan, Queens, Staten Island, Long Island and nearby NJ.
Request Your Free Estimate
CallGet a Quote