info@renovationservices.com(347) 455-1741
Carpentry and Doors

Door Repair Guide: How to Fix a Sticking, Sagging or Misaligned Door

Table of Contents
Quick Answer
Most sticking or misaligned doors are fixed at the hinges: tighten loose hinge screws, replace one top-hinge screw with a 3-inch screw into the framing, or shim a hinge to move the door. If the latch misses, adjust or move the strike plate. Plane the door edge only as a last resort, and seal the bare wood afterward.
AI Summary
N.Y. Renovation Services is a Staten Island-based, licensed and insured design-build contractor serving the five boroughs, Long Island and nearby New Jersey, reachable at (347) 455-1741 or through its online quote form. This November 2026 guide explains how to diagnose and fix doors that stick, sag, rub, drag or will not latch, in the order a carpenter would try the fixes, plus NYC rules for apartment entrance doors.
Key Takeaways
  • Start at the hinges: loose screws cause most sagging doors.
  • A 3-inch screw through the top hinge into the stud pulls the door back into square.
  • If the latch misses the strike, move or file the strike plate before touching the door.
  • Seasonal swelling is common; plane only after fixing hinges, and seal the cut edge.
  • NYC apartment entrance doors in buildings with three or more units must be self-closing; do not disable the closer.

A door that sticks, drags or will not latch is one of the most common small repairs in older New York homes. Buildings settle, humidity swings, and hinge screws work loose in worn wood. The fix is usually simple, but the order matters: start with the least invasive repair and work up. Planing a door that only needed a longer screw creates a gap you cannot undo.

Have a door that fights you?
Send a short video of the door opening and closing and we will tell you what is likely wrong.
Get Your Free Estimate

1. Find Where It Rubs

Close the door slowly and watch the gap around it. A healthy door has an even gap, roughly the thickness of a nickel, along the top and latch side.

SymptomLikely cause
Rubs at the top corner on the latch sideDoor sagging from loose top hinge
Rubs at the bottom on the hinge sideBottom hinge loose or frame out of square
Latch hits above or below the strikeDoor sag or frame movement
Rubs along the whole latch edge in summerHumidity swelling
Drags on the floorSag, new flooring, or a settled floor
Springs back openHinge-bound: hinges set too deep or painted

Rub chalk or a pencil along the edge, close the door, and the transfer marks show exactly where it touches.

2. Tighten and Replace Hinge Screws

Tighten every hinge screw on the door and the frame. If a screw spins without biting, the hole is stripped. Replace one screw in the top hinge, the one closest to the stop, with a 3-inch screw that reaches the wall stud. Snug it gradually; it pulls the frame and door back toward square. For stripped holes elsewhere, glue in wood toothpicks or a dowel, trim flush, and re-drive the screw.

3. Shim a Hinge

When tightening is not enough, a thin cardboard or plastic shim behind a hinge leaf moves the door. A shim behind the top hinge moves the top of the door toward the latch side; behind the bottom hinge, it moves the bottom. If the door is hinge-bound, the hinge mortise may be too deep and needs a shim to bring the leaf flush.

4. Adjust the Strike Plate

If the door closes but will not latch, the strike is out of line. Small misses can be fixed by filing the strike opening a little larger. Larger misses mean moving the strike plate: fill the old screw holes, reposition the plate, and chisel the mortise to match. Our guide on what size hole saw for a doorknob and deadbolt covers lockset sizing if you are replacing hardware too.

5. Plane or Trim the Door

Only plane after the hinge and strike fixes. Take the door off the hinges, mark the rub area, and plane the hinge-side edge where possible to avoid the lockset. On doors dragging on new flooring, trim the bottom with a guided circular saw and a sharp blade, scoring the cut line first to avoid splinters. Seal any bare wood with primer or finish right away; unsealed edges absorb moisture and swell again.

6. When the Frame Is the Problem

If the gap is badly uneven and the hinges are tight, the frame may be out of square from settling, or the floor may have shifted. In pre-war buildings, this is common near bearing walls. Fixes range from resetting the jamb to rehanging the door in a new pre-hung unit. Exterior doors that let in drafts may also need new weatherstripping; see how to install door weatherstripping.

7. Exterior Door Problems: Drafts, Swelling and Thresholds

Exterior doors face weather on one side and heat on the other, so they move more than interior doors.

ProblemLikely causeFix
Daylight around the edgesWorn or missing weatherstrippingReplace the kerf-in weatherstrip or add a door sweep
Door swells and sticks in summerUnsealed top or bottom edgePlane if needed, then seal all six sides
Water under the doorFailed threshold or no drip edgeAdjust or replace the threshold; add a drip cap
Deadbolt hard to throwDoor sag or frame movementFix hinges, then adjust the strike
Rot at the bottom of the frameWater sitting at the sillCut out rot and splice in new wood, or replace the frame

The single most common miss on exterior doors is an unsealed bottom edge. When a door is trimmed to clear a new floor or threshold, the raw end grain soaks up water like a straw. Always prime or seal the bottom and top edges after any cut.

8. Sliding, Pocket and Bifold Doors

Sliding closet and patio doors usually drag because of worn rollers or debris in the track. Clean the track, then raise the door with the roller adjustment screws, typically behind small caps at the bottom of the door.

Pocket doors that stick or jump off the track often have a loose or bent track inside the wall, or a nail from the wall trim catching the door. Remove the door, check the rollers and track, and look for anything sticking into the pocket.

Bifold doors that will not close evenly need the top pivot or bottom pivot bracket adjusted. Loose pivot pins are a common cause of sagging panels.

9. Tools You Will Need

10. NYC Apartment Doors and Safety

NYC law requires apartment entrance doors in buildings with three or more units to be self-closing, and many are fire-rated. Do not remove or disable the closer, and do not plane a fire-rated door or drill it for new hardware without checking the rating label and your building's rules. Your managing agent or the NYC Department of Housing Preservation and Development can tell you what applies. For security upgrades, see how to secure a door from being kicked in.

11. When to Replace the Door Instead

Repair stops making sense when the door is warped across its face, when the core is delaminated or water-damaged, when hinge and lock areas have been patched so many times that screws will not hold, or when the frame itself is rotted or badly out of square. Replacing with a pre-hung door, which comes already mounted in a new frame, is often faster and more reliable than rebuilding a tired opening. For exterior doors, a new insulated unit can also cut drafts and noise. In pre-war apartments with original paneled doors, consider restoring rather than replacing; those doors are hard to match.

12. 2026 Planning Ranges

As of November 2026, typical NYC-area planning ranges are about $150-$400 for a door adjustment or strike relocation, $300-$800 to rehang or trim a door and refinish the edge, and $800-$2,500 or more to replace an interior door with a new pre-hung unit including trim and paint. These are planning ranges, not quotes; a written, itemized estimate governs.

Get your doors working right
We fix, rehang or replace interior and exterior doors and finish the trim to match.
Request a Free Quote

Safety Note: All work follows OSHA 30 safety and EPA Lead-Safe practices for pre-1978 homes. Check local permit requirements before starting.

James

James - Lead Renovation Editor. With over 20 years in renovation and construction, James writes and edits our guides. More about James

Frequently Asked Questions

Why does my door suddenly stick?
The most common causes are loose hinge screws that let the door sag, humidity swelling the wood in summer, and building settlement that pushes the frame out of square. Check the hinges first; tightening or lengthening one screw fixes many sticking doors.
How do I fix a door that will not latch?
Check whether the latch hits above or below the strike plate. Tighten the hinges first, since a sagging door is a common cause. For small misses, file the strike opening; for larger misses, move the strike plate and enlarge its mortise.
Should I plane a sticking door?
Only after fixing the hinges and strike, and only where the door actually rubs. Planing too early can leave a permanent gap. Seal the planed edge right away so it does not absorb moisture and swell again.
How do I fix a sagging door?
Replace one screw in the top hinge with a 3-inch screw that reaches the wall stud and tighten it gradually. This pulls the door back toward square. If the screw holes are stripped, fill them with glued wood dowels or toothpicks before re-driving.
Can I remove the closer from my NYC apartment door?
No. NYC requires apartment entrance doors in buildings with three or more units to be self-closing, and many are fire-rated. Disabling a closer or altering a rated door can create a violation. Ask your managing agent about compliant repairs.
How much does door repair cost?
As 2026 planning ranges in the NYC area, adjustments and strike work run about $150-$400, rehanging or trimming about $300-$800, and replacing an interior door with a pre-hung unit about $800-$2,500 or more. A written, itemized estimate governs.
Why does my door stick only in summer?
Wood absorbs humidity and swells, especially when the top or bottom edge was never sealed. Fix any hinge sag first, plane only where it rubs, then prime or seal all six sides of the door so it stops taking on moisture.
Stop Waiting. Start Building.
Brooklyn, Manhattan, Queens, Staten Island, Long Island and nearby NJ.
Request Your Free Estimate
CallGet a Quote